BAD83防爆無極燈 ，BEW防爆無極燈 ccd92防爆無極燈，ccd93系列防爆無極燈 ，BAD81防爆無極燈 BAD83系列防爆無極燈是公司主打產品之一 價格和質量也是防爆行業的標準 是公司銷量的產品  以此本公司向廣大客戶推薦此類產品 望廣大客戶前來咨詢訂購

BAD83防爆無極燈 ，BEW防爆無極燈 ccd92防爆無極燈，ccd93系列防爆無極燈 ，BAD81防爆無極燈 BAD83系列防爆無極燈是公司主打產品之一 價格和質量也是防爆行業的標準 是公司銷量的產品  以此本公司向廣大客戶推薦此類產品 望廣大客戶前來咨詢訂購

一，主要適用于爆炸性氣體環境中1區或2區危險區域，為ⅡC或ⅡB類T2組及以下場所，在交流50Hz、額定電壓至220V的電路中，作為工作場所照明之用。

二，BAD83防爆無極燈主要結構防爆燈由鋁合金外殼、玻璃罩和保護網等幾部分組成。隔爆型機構。防爆燈的外殼采用ZL102鑄鋁合金壓鑄制成，玻璃罩采用鋼化玻璃制成。防爆燈設有內外接地螺釘和接線腔，適合電纜或鋼管布線。防爆燈可有多種安裝方式，采用快速拆裝結構，便于快速更換燈泡。一體式防爆燈，鎮流器可放入燈體內，外型美觀，分體式防爆燈，鎮流器需另配。

三，BAD83防爆無極燈防爆燈在下列條件下能夠可靠工作 1、安裝地點的海拔不限制。 2、周圍環境溫度為-20℃～+40℃時，且24h內的平均值不超過35℃ 3、安裝地點的空氣相對濕度在溫度為+40℃時，不超過50%，在較低的溫度下允許有較高的相對濕度，濕的月平均溫度不超過+25℃，該月平均相對濕度不超過90%。 4、在無劇烈振動，沖擊及搖動的地方。 5、在含有爆炸性氣體環境場所。 6、污染等級為3級。

四、BAD83防爆無極燈使用及維修 1、防爆燈在安裝前，應檢查銘牌上所列技術數據及使用說明書中的基本參數是否與實際使用情況相符，并檢查元件是否損壞、各部位是否完好、正常。安裝時先將進線電纜通過引入裝置接到接線腔的接線端子上，并壓緊密封圈，使電纜密封好，接好接地線，緊固好螺釘，上述各項檢查無誤后，既可通電使用。 2、防爆燈不得隨意拆卸，維護時，須斷開前級電源后才可開蓋檢修或更換燈泡。 3、在維修過程中不得損壞隔爆面，維修后涂204-1防銹油，合好蓋，緊固后方可使用。 4、防爆燈應定期檢查，發現零件損壞應及時更換。 BAD83防爆無極燈 BEW防爆無極燈 ccd92防爆無極燈ccd93系列防爆無極燈 BAD81防爆無極燈

近年來，貴公司堅持以市場為導向，銳意進取，開拓創新，不斷培育以技術創新為基礎的競爭力，在激烈的市場競爭中迅速崛起，成為中國防爆行業的主導企業之一，建立了現代企業規章制度。
公司始終堅持“客戶至上，質量”的宗旨，以不斷創新和對客戶滿意的服務贏得市場。歡迎新老客戶前來訂購洽談.

Mainly suitable for explosive gas atmospheres of Zone 1 or Zone 2 hazardous areas, Ⅱ C or the Ⅱ B class T2 group and the following places in AC 50Hz, rated voltage up to 220V circuit, used as a workplace lighting.

Two BAD83 explosion-proof induction lamp structure explosion-proof lamps aluminum alloy shell, glass and protection network consisting of several parts. The flameproof institutions. The shell is made of explosion-proof lights ZL102 cast aluminum alloy and glass tempered glass. The explosion-proof lights with internal and external ground screw and wiring cavity, suitable cable or steelpipe. The explosion-proof lights can have a variety of installation methods, the use of the rapid dismantling the structure, quick and easy lamp replacement. Integrated explosion-proof lamps, ballasts can be placed in the lamp body, good looks, split explosion-proof lamps, ballasts need to reprovision.

Explosion-proof, BAD83 explosion-proof induction lamp lights under the following conditions can be reliably work 1, does not restrict the altitude of the installation site. 2, the ambient temperature of -20 ° C to +40 ° C, and the mean value is not more than 35 ° C within 24h, the installation location of the air relative humidity not more than 50% at a maximum temperature of +40 ° C, at a lower the temperature allows a higher relative humidity, the wettest month average minimum temperature does not exceed +25 ° C, the maximum average monthly relative humidity does not exceed 90%. 4, severe vibration, shock and shake the place. 5 containing explosive gas atmospheres places. 6, the pollution level of the three.

, BAD83 explosion-proof induction lamp and maintenance of an explosion-proof lamps should check the nameplate on the basic parameters listed in the technical data and manual in line with the actual usage, and check the components for damage before installing, each part is intact. properly. First incoming cable installation by introducing a device connected to the terminals of the wiring chamber and compress the seal, the cable sealed, connect the ground wire to tighten the screws, the above examinations correct, both energized to use. 2, explosion-proof lights shall not disassemble, maintenance former level power should be disconnected before opening the lid to repair or replace the lamp. 3, in the maintenance process shall not damage the flameproof surface maintenance coating 204-1 after anti-rust oil, Hao cover, fastening before use. 4, explosion-proof lights should be checked regularly to find parts damage should be replaced. Promise lights, BAD83 explosion-proof BEW the explosion electrodeless lamp ccd92 explosion-proof Promise the lights ccd93 series explosion-proof Promise the lights BAD81 explosion-proof induction lamp

In recent years, the company adhere to market-oriented, forge ahead, pioneering and innovative, constantly cultivating core competitiveness based on technological innovation in the fierce market competition, rapid rise to become one of the leading enterprises of China's proof industry established The modern corporate rules and regulations.
The company always adhere to the "customer first, quality first" purpose, innovation and the customer satisfaction service to win the market. Welcome to the new and old customers come to order to negotiate

 世人都犯了罪 虧缺了神的榮耀 神愛世人 將他的獨生子【耶穌】賜給我們 為我們的罪釘死在十字架上 搭建了世人去天堂的路   神說；他就是生命 就是光 。光照在黑暗里 黑暗卻不接受光。 朋友 認識耶和華是智慧的開端 回來吧  愿神祝福您

BAD83防爆無極燈 ，BEW防爆無極燈 ccd92防爆無極燈，ccd93系列防爆無極燈 ，BAD81防爆無極燈 BAD83系列防爆無極燈是公司主打產品之一 價格和質量也是防爆行業的標準 是公司銷量的產品  以此本公司向廣大客戶推薦此類產品 望廣大客戶前來咨詢訂購

一，主要適用于爆炸性氣體環境中1區或2區危險區域，為ⅡC或ⅡB類T2組及以下場所，在交流50Hz、額定電壓至220V的電路中，作為工作場所照明之用。

二，BAD83防爆無極燈主要結構防爆燈由鋁合金外殼、玻璃罩和保護網等幾部分組成。隔爆型機構。防爆燈的外殼采用ZL102鑄鋁合金壓鑄制成，玻璃罩采用鋼化玻璃制成。防爆燈設有內外接地螺釘和接線腔，適合電纜或鋼管布線。防爆燈可有多種安裝方式，采用快速拆裝結構，便于快速更換燈泡。一體式防爆燈，鎮流器可放入燈體內，外型美觀，分體式防爆燈，鎮流器需另配。

三，BAD83防爆無極燈防爆燈在下列條件下能夠可靠工作 1、安裝地點的海拔不限制。 2、周圍環境溫度為-20℃～+40℃時，且24h內的平均值不超過35℃ 3、安裝地點的空氣相對濕度在溫度為+40℃時，不超過50%，在較低的溫度下允許有較高的相對濕度，濕的月平均溫度不超過+25℃，該月平均相對濕度不超過90%。 4、在無劇烈振動，沖擊及搖動的地方。 5、在含有爆炸性氣體環境場所。 6、污染等級為3級。

四、BAD83防爆無極燈使用及維修 1、防爆燈在安裝前，應檢查銘牌上所列技術數據及使用說明書中的基本參數是否與實際使用情況相符，并檢查元件是否損壞、各部位是否完好、正常。安裝時先將進線電纜通過引入裝置接到接線腔的接線端子上，并壓緊密封圈，使電纜密封好，接好接地線，緊固好螺釘，上述各項檢查無誤后，既可通電使用。 2、防爆燈不得隨意拆卸，維護時，須斷開前級電源后才可開蓋檢修或更換燈泡。 3、在維修過程中不得損壞隔爆面，維修后涂204-1防銹油，合好蓋，緊固后方可使用。 4、防爆燈應定期檢查，發現零件損壞應及時更換。 BAD83防爆無極燈 BEW防爆無極燈 ccd92防爆無極燈ccd93系列防爆無極燈 BAD81防爆無極燈

近年來，貴公司堅持以市場為導向，銳意進取，開拓創新，不斷培育以技術創新為基礎的競爭力，在激烈的市場競爭中迅速崛起，成為中國防爆行業的主導企業之一，建立了現代企業規章制度。
公司始終堅持“客戶至上，質量”的宗旨，以不斷創新和對客戶滿意的服務贏得市場。歡迎新老客戶前來訂購洽談.

Mainly suitable for explosive gas atmospheres of Zone 1 or Zone 2 hazardous areas, Ⅱ C or the Ⅱ B class T2 group and the following places in AC 50Hz, rated voltage up to 220V circuit, used as a workplace lighting.

Two BAD83 explosion-proof induction lamp structure explosion-proof lamps aluminum alloy shell, glass and protection network consisting of several parts. The flameproof institutions. The shell is made of explosion-proof lights ZL102 cast aluminum alloy and glass tempered glass. The explosion-proof lights with internal and external ground screw and wiring cavity, suitable cable or steelpipe. The explosion-proof lights can have a variety of installation methods, the use of the rapid dismantling the structure, quick and easy lamp replacement. Integrated explosion-proof lamps, ballasts can be placed in the lamp body, good looks, split explosion-proof lamps, ballasts need to reprovision.

Explosion-proof, BAD83 explosion-proof induction lamp lights under the following conditions can be reliably work 1, does not restrict the altitude of the installation site. 2, the ambient temperature of -20 ° C to +40 ° C, and the mean value is not more than 35 ° C within 24h, the installation location of the air relative humidity not more than 50% at a maximum temperature of +40 ° C, at a lower the temperature allows a higher relative humidity, the wettest month average minimum temperature does not exceed +25 ° C, the maximum average monthly relative humidity does not exceed 90%. 4, severe vibration, shock and shake the place. 5 containing explosive gas atmospheres places. 6, the pollution level of the three.

, BAD83 explosion-proof induction lamp and maintenance of an explosion-proof lamps should check the nameplate on the basic parameters listed in the technical data and manual in line with the actual usage, and check the components for damage before installing, each part is intact. properly. First incoming cable installation by introducing a device connected to the terminals of the wiring chamber and compress the seal, the cable sealed, connect the ground wire to tighten the screws, the above examinations correct, both energized to use. 2, explosion-proof lights shall not disassemble, maintenance former level power should be disconnected before opening the lid to repair or replace the lamp. 3, in the maintenance process shall not damage the flameproof surface maintenance coating 204-1 after anti-rust oil, Hao cover, fastening before use. 4, explosion-proof lights should be checked regularly to find parts damage should be replaced. Promise lights, BAD83 explosion-proof BEW the explosion electrodeless lamp ccd92 explosion-proof Promise the lights ccd93 series explosion-proof Promise the lights BAD81 explosion-proof induction lamp

In recent years, the company adhere to market-oriented, forge ahead, pioneering and innovative, constantly cultivating core competitiveness based on technological innovation in the fierce market competition, rapid rise to become one of the leading enterprises of China's proof industry established The modern corporate rules and regulations.
The company always adhere to the "customer first, quality first" purpose, innovation and the customer satisfaction service to win the market. Welcome to the new and old customers come to order to negotiate

 世人都犯了罪 虧缺了神的榮耀 神愛世人 將他的獨生子【耶穌】賜給我們 為我們的罪釘死在十字架上 搭建了世人去天堂的路   神說；他就是生命 就是光 。光照在黑暗里 黑暗卻不接受光。 朋友 認識耶和華是智慧的開端 回來吧  愿神祝福您

一，主要適用于爆炸性氣體環境中1區或2區危險區域，為ⅡC或ⅡB類T2組及以下場所，在交流50Hz、額定電壓至220V的電路中，作為工作場所照明之用。

二，BAD83防爆無極燈主要結構防爆燈由鋁合金外殼、玻璃罩和保護網等幾部分組成。隔爆型機構。防爆燈的外殼采用ZL102鑄鋁合金壓鑄制成，玻璃罩采用鋼化玻璃制成。防爆燈設有內外接地螺釘和接線腔，適合電纜或鋼管布線。防爆燈可有多種安裝方式，采用快速拆裝結構，便于快速更換燈泡。一體式防爆燈，鎮流器可放入燈體內，外型美觀，分體式防爆燈，鎮流器需另配。

三，BAD83防爆無極燈防爆燈在下列條件下能夠可靠工作 1、安裝地點的海拔不限制。 2、周圍環境溫度為-20℃～+40℃時，且24h內的平均值不超過35℃ 3、安裝地點的空氣相對濕度在溫度為+40℃時，不超過50%，在較低的溫度下允許有較高的相對濕度，濕的月平均溫度不超過+25℃，該月平均相對濕度不超過90%。 4、在無劇烈振動，沖擊及搖動的地方。 5、在含有爆炸性氣體環境場所。 6、污染等級為3級。

四、BAD83防爆無極燈使用及維修 1、防爆燈在安裝前，應檢查銘牌上所列技術數據及使用說明書中的基本參數是否與實際使用情況相符，并檢查元件是否損壞、各部位是否完好、正常。安裝時先將進線電纜通過引入裝置接到接線腔的接線端子上，并壓緊密封圈，使電纜密封好，接好接地線，緊固好螺釘，上述各項檢查無誤后，既可通電使用。 2、防爆燈不得隨意拆卸，維護時，須斷開前級電源后才可開蓋檢修或更換燈泡。 3、在維修過程中不得損壞隔爆面，維修后涂204-1防銹油，合好蓋，緊固后方可使用。 4、防爆燈應定期檢查，發現零件損壞應及時更換。 BAD83防爆無極燈 BEW防爆無極燈 ccd92防爆無極燈ccd93系列防爆無極燈 BAD81防爆無極燈

近年來，貴公司堅持以市場為導向，銳意進取，開拓創新，不斷培育以技術創新為基礎的競爭力，在激烈的市場競爭中迅速崛起，成為中國防爆行業的主導企業之一，建立了現代企業規章制度。
公司始終堅持“客戶至上，質量”的宗旨，以不斷創新和對客戶滿意的服務贏得市場。歡迎新老客戶前來訂購洽談.

Mainly suitable for explosive gas atmospheres of Zone 1 or Zone 2 hazardous areas, Ⅱ C or the Ⅱ B class T2 group and the following places in AC 50Hz, rated voltage up to 220V circuit, used as a workplace lighting.

Two BAD83 explosion-proof induction lamp structure explosion-proof lamps aluminum alloy shell, glass and protection network consisting of several parts. The flameproof institutions. The shell is made of explosion-proof lights ZL102 cast aluminum alloy and glass tempered glass. The explosion-proof lights with internal and external ground screw and wiring cavity, suitable cable or steelpipe. The explosion-proof lights can have a variety of installation methods, the use of the rapid dismantling the structure, quick and easy lamp replacement. Integrated explosion-proof lamps, ballasts can be placed in the lamp body, good looks, split explosion-proof lamps, ballasts need to reprovision.

Explosion-proof, BAD83 explosion-proof induction lamp lights under the following conditions can be reliably work 1, does not restrict the altitude of the installation site. 2, the ambient temperature of -20 ° C to +40 ° C, and the mean value is not more than 35 ° C within 24h, the installation location of the air relative humidity not more than 50% at a maximum temperature of +40 ° C, at a lower the temperature allows a higher relative humidity, the wettest month average minimum temperature does not exceed +25 ° C, the maximum average monthly relative humidity does not exceed 90%. 4, severe vibration, shock and shake the place. 5 containing explosive gas atmospheres places. 6, the pollution level of the three.

, BAD83 explosion-proof induction lamp and maintenance of an explosion-proof lamps should check the nameplate on the basic parameters listed in the technical data and manual in line with the actual usage, and check the components for damage before installing, each part is intact. properly. First incoming cable installation by introducing a device connected to the terminals of the wiring chamber and compress the seal, the cable sealed, connect the ground wire to tighten the screws, the above examinations correct, both energized to use. 2, explosion-proof lights shall not disassemble, maintenance former level power should be disconnected before opening the lid to repair or replace the lamp. 3, in the maintenance process shall not damage the flameproof surface maintenance coating 204-1 after anti-rust oil, Hao cover, fastening before use. 4, explosion-proof lights should be checked regularly to find parts damage should be replaced. Promise lights, BAD83 explosion-proof BEW the explosion electrodeless lamp ccd92 explosion-proof Promise the lights ccd93 series explosion-proof Promise the lights BAD81 explosion-proof induction lamp

In recent years, the company adhere to market-oriented, forge ahead, pioneering and innovative, constantly cultivating core competitiveness based on technological innovation in the fierce market competition, rapid rise to become one of the leading enterprises of China's proof industry established The modern corporate rules and regulations.
The company always adhere to the "customer first, quality first" purpose, innovation and the customer satisfaction service to win the market. Welcome to the new and old customers come to order to negotiate

 世人都犯了罪 虧缺了神的榮耀 神愛世人 將他的獨生子【耶穌】賜給我們 為我們的罪釘死在十字架上 搭建了世人去天堂的路   神說；他就是生命 就是光 。光照在黑暗里 黑暗卻不接受光。 朋友 認識耶和華是智慧的開端 回來吧  愿神祝福您