產 品 規 格 書
PRODU SPECIFICATION
【1】適用范圍 SCOPE
本規格書適用于：0.5間距柔性扁平電纜連接器（有鎖式）
This specification covers the 0.5mm Pitch FPC/FFC Conneors（series Locking）
【2】產品名稱及型號 PRODU NAME AND PART NUER
產品名稱Produ Name | 產品型號Part Nuer |
FFC/FPC扁平電纜連接器 |
|
|
|
【3】定格 RATINGS
項目 Item | 規 格 Requirement | ||
容許電壓 Rated Voltage(MAX) | 50V | [AC/DC(值 Virtual value)50Hz] | |
容許電流 Rated Current(MAX) | 0.4A | ||
使用溫度范圍 Aienttemperature Range | -25℃～ +85℃ | ||
【4】性能 PERFORMANCE
4.1電氣性能 Elerical Performance
項目Item | 條 件 Test Condition | 規格Requirement | |
4.1.1 | 接觸電阻 Conta Resistance | 適合FPC/FFC嵌合；開放電壓20mV以下；短路電流10mA的狀態下測定。 Mate applicable FPC/FFC and measure by dry circuit，20mV MAX，10mA. | ≤20 mΩMAX |
4.1.2 |
緣電阻 Insulation Resistance | 適合FPC/FFC嵌合；相鄰端子間或端子與地面間加DC 500V下測定。 Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground. | 500MΩMIN |
4.1.3 |
耐電壓 Dieleric | 適合FPC/FFC嵌合；相鄰端子間或端子與地面間加AC 200V（值）歷時1分鐘下測定。 Mate applicable FPC/FFC and apply 200V AC（virtual value）for 1minute between adjacent terminal or ground. | 無擊穿現象 No Breakdown |
4.2機械性能 Mechanical Performance
項目Item | 條 件 Test Condition | 規格Requirement | |
4.2.1 | 鎖緊力及拔出力 Locking and Withdrawal Force | 適合0.3mm厚的FFC；用每分鐘25&plun;3mm的速度；平行地、鎖緊、拔出。 Insert and extra applicable FFC at the speed rate of 25&plun;3mm/minute. | 鎖緊力Locking 1.96*n (N) MAX 拔出力Withdrawal 0.49*n (N) MIN |
4.2.2 | 端子保持力 Terminal /Housing Retention Force | 以用每分鐘25&plun;3mm的速度平行向外拉 Pull the terminal at the speed rate of 25&plun;3mm per minute | 3.92N MIN |
4.3環境和其他性能 Environmental Performance and Others
項目Item | 條 件 Test Condition | 規格Requirement | ||
4.3.1 | 重復插拔 Repeated Insertion and Withdrawal | 無通電狀態；以10次/分鐘的速度插拔20次 Insertion and withdrawal auator up to 20 cycles at the speed rate of less than 10 cycles/minute | 接觸 Conta Resistance | 60 mΩMAX |
4.3.2 | 溫度上升 Temperature Rise | 適合FPC/FFC嵌合；容許電流通電，溫度測定。（UL 498） Carrying rated current load.（UL 498） | 溫度上升 Temperature Rise | 30℃MAX |
項目Item | 條 件 Test Condition | 規格Requirement | ||
4.3.3 |
耐振動性 Vibration | DC 1mA通電狀態下；嵌合軸沿XYZ三個方向振動；振幅1.5mm；頻率10-55-10Hz/分；歷時2小時 Amplitude：1.5mm P-P Sweep time：10-55-10Hz in 1 minute Duration：2 hours in each X.Y.Z. axes | 外觀 Appearance | 壞 No Damage |
接觸 Conta Resistance | 60 mΩMAX | |||
瞬斷 Discontinuity | 1 ms MAX. | |||
4.3.4 |
耐沖擊性 Shock | DC 1mA通電狀態下；嵌合軸沿相互垂直的6個方向；以490m/s2{50G}沖擊；各3次 490m/s2{50G}，3 strokes in each X.Y.Z. axes. | 外觀 Appearance | 壞 No Damage |
瞬斷 Discontinuity | 1 ms MAX. | |||
4.3.5 |
耐熱性 Heat Resistance | 適合FPC/FFC嵌合；85&plun;2℃的空氣中；放置96小時；再回到室溫中放置1-2小時 85&plun;2℃，96 hour | 外觀 Appearance | 壞 No Damage |
接觸 Conta Resistance | 60 mΩMAX | |||
4.3.6 |
耐寒性 Cold Resistance | 適合FPC/FFC嵌合；-40&plun;2℃的空氣中；放置96小時；再回到室溫中放置1-2小時 -40&plun;2℃，96 hour | 外觀 Appearance | 壞 No Damage |
接觸 Conta Resistance | 60 mΩMAX | |||
4.3.7 |
耐濕性 Humidity |
適合FPC/FFC嵌合；40&plun;2℃、相對濕度90-95%的空氣中；放置96小時；再回到室溫中0.5小時內測定
Temperature：40&plun;2℃ Relative Humidity：90-95% Duration：96 Hours | 外觀 Appearance | 壞 No Damage |
接觸 Conta Resistance | 60 mΩMAX | |||
耐電壓 Dieleric Strength | 須滿足4.1.3 Must meet 4.1.3 | |||
緣 Insulation Resistance | 20 MΩMIN | |||
4.3.8 |
溫度循環 Temperature Cycling | 適合FPC/FFC嵌合；-55&plun;3℃ 30分鐘；常溫常濕 10-15分鐘；85&plun;2℃ 30分鐘；常溫常濕 10-15分鐘，循環5次。 5 cycles of： a) -55&plun;3℃ 30 minutes b) 85&plun;2℃ 30 minutes | 外觀 Appearance | 壞 No Damage |
接觸 Conta Resistance | 60 mΩMAX | |||
項目Item | 條 件 Test Condition | 規格Requirement | ||
4.3.9 |
耐鹽霧性 Salt Spray | 適合FPC/FFC嵌合；35&plun;2℃、5&plun;1%的鹽水噴霧48小時；試驗后常溫水洗；再室溫干燥。 48&plun;4 hours exposure to a salt spray from the 5&plun;1% solution at 35&plun;2℃. | 外觀 Appearance | 壞、腐蝕 No Damage |
接觸 Conta Resistance | 60 mΩMAX | |||
4.3.10 |
耐亞 SO2 Gas | 適合FPC/FFC嵌合；40&plun;2℃、50&plun;5ppm的亞中放置24小時 24 hours exposure to 50&plun;5ppm. SO2 gas at 40&plun;2℃. | 接觸 Conta Resistance | 60 mΩMAX |
4.3.11 |
耐氨性 NH3 Gas | 適合FPC/FFC嵌合；濃度為28%的容器中；放置40分鐘。 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution | 外觀 Appearance | 壞 No Damage |
接觸 Conta Resistance | 60 mΩMAX | |||
4.3.12 |
可焊性 Solder ability | 端子前端基準面0.2mm處浸入235&plun;5℃的錫槽中；歷時2&plun;0.5 sec。 Soldering Time：2&plun;0.5 sec. Soldering Temperature：235&plun;5℃ 0.2 mm from terminal tip | 沾敷性 Solder Wetting | 沾敷面積95%以上
|
4.3.13 |
耐焊接熱 Resistance to Soldering heat | 端子前端基準面0.2mm處浸入260&plun;5℃的錫槽中；歷時5&plun;0.5 sec。 Soldering Time：5&plun;0.5 sec. Soldering Temperature：260&plun;5℃ 0.2 mm from terminal tip | 外觀 Appearance | 壞、變形 No Damage |
( )：參考規格Reference Standard
{ }：參考單位Reference Unit
【5】外觀形狀、寸法及材質PRODU SHAPE,DIMENSIONS AND MATERIALS
圖面參照 Refer to the drawing.
名稱 NAME | 材質 MATERIALS |
主體Main body | LCP(本色) UL 94V-0 |
鎖扣Housing Lock | LCP(黑色) UL 94V-0 |
端子Sit uip | 磷青銅 Phosphor Bronze |
焊片Conta | 磷青銅 Phosphor Bronze |
備注Remark | 金屬表面鍍錫 |
